Customers compare hm74113 to these similar products
Products Featured in this Video
Today we're going to take a look at the Hopkins collapsible truck organizer with mesh bins part number HM74113. This organizer is perfect for tidying up a cluttered trunk or cargo area. As you can see our organizer's going to slide right into place, gives us a nice area to load up all of our stuff and keep it organized. Here on the bottom, you're going to have four flat spots. That's going to be… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
If you were to install the Curt #31302 Front Mount Hitch so that it is the "through bumper" instead of "under bumper" configuration you will need to cut out a 3 inch square hole that is located 3-1/2 inches below the top edge of…
view full answer...The install of the Curt front hitch part #31302 that fits your 2003 Chevy Silverado 1500 Z71 does not require the permanent removal of the tow hooks.
view full answer...For a through-fascia installation, the instructions state that the top of the 3 inch square hole would fall 3-1/2 inches below the top edge of the plastic fascia. Before cutting, I would strongly recommend you confirm these measurements for yourself.…
view full answer...There is absolutely no drilling at all needed to install the Curt Trailer Hitch Receiver #C67JR on your 2020 Subaru Outback; installing the hitch will use a combination of your Subaru's existing hardware and the included bolts. In regards to…
view full answer...The Hopkins Collapsible Vehicle Cargo Organizer #HM74113 is a multi-vehicle fit item, so I don't have any fit information for specific vehicles. However, you can see the dimensions of the organizer in the photo I've edited for you. Simply…
view full answer...The Camco Olympian Wave 3 Catalytic Safety Heater #CAM57331 can be mounted at an angle, but only up to a 10 degree angle so you wouldn't be able to mount this on the ceiling or at a 45 degree angle unfortunately. We do carry the Leg Stands…
view full answer...In order to haul a generator on the front of your vehicle, I suggest using a front mount trailer hitch such as the #13703. This is an adjustable type hitch that fits frames from 22" to 72" in width. It is not a custom fit but will require a…
view full answer...When looking at the Draw-Tite Hitch #DT73RR and the #e25TR, there are some differences to consider. The first thing is the weight capacity. The #DT73RR offers 675 pounds of tongue weight/4,500 pounds of gross towing weight while the #e25TRonly offers…
view full answer...We have versions of the Rhino Rack Pioneer Platform that were designed for attaching to crossbars like the part #RR42114BF for a 48 by 38 inch platform or part #RR42115BF for a 58 by 47 inch platform. Both of these would attach to a Wingbar rack.
view full answer...There isn't a fit kit that allows the Rhino-Rack Pioneer alloy trays to fit the Thule AeroBlade Edge crossbars but I do have a solution for you. You could use the Thule Trail basket #TH864XT with the AeroBlade Edge roof rack, #TH7502B-TH7503B, on…
view full answer...For trailer wiring the brand we have the best luck with is Tekonsha. They are the most reliable and overall give us the fewest problems. The majority of the time we have an issue with a wiring harness it's a Curt brand. And they've redesigned…
view full answer...Thank you for including a photo of your tube steps for which you need replacement step pads. The measurement of the mounting posts (12-1/2-inches apart) is helpful too. Unfortunately without knowing the manufacturer of the bars I cannot be absolutely…
view full answer...